Home > Hp Laptop > Can Not Get Passed HP Logo Screen When Powering On

Can Not Get Passed HP Logo Screen When Powering On

Contents

If the computer still does not start and exhibits the same problem, continue the troubleshooting. When the login prompt displays, select the user name with Administrator rights (not Administrator) from the User Name drop down. Be careful not to slide skin along any interior metal edge of the computer. Read and respond to any screens that open. navigate to this website

Turn on the computer. Hard drive is not detected in BIOS Select your type of computer from the options below, then follow the instructions for that type of computer. If the startup problem is gone, you are finished but you may want to update the BIOS if one is available for your model of computer. Remove any screws that connect the panel to the computer.

Hp Laptop Wont Boot Windows 10

Step 2: Reseat the hard drive in an All-in-One or HP TouchSmart To reseat the hard drive, perform the following steps: note: For detailed instructions, open HP Customer Support, enter the Plug the power cable back into the computer. If you find a symptom that matches your computer's symptom, click the corresponding link. IDE: Make sure the jumper setting and cable connections are correct.

Select Repair Your Computer, and then press Enter. Status BAD, Backup and Replace To resolve SMART error messages, see Hard Drive Failure Errors. Click Next. Hp Desktop Wont Boot Past Hp Screen If the AC power adapter is not damaged, continue using these steps.

I did exactly what you told me and her laptop is functional again. Hp Computer Won't Boot Past Hp Screen Complementary Content Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! If the computer starts, you are done. Figure : Choose an option screen Click Refresh your PC.

It's locked there. Hp Computer Won't Boot Past Blue Screen Doing so can void your warranty. Additional batteries are affected. No success means it is time to try the other module in the same manner.If no joy with the preceding troubleshooting put both memory modules back in their respective DIMM slots.Disconnect

Hp Computer Won't Boot Past Hp Screen

System Information Start-Up Test Run-In Test Hard Disk Test Memory Test Battery Test Error Log Exit Figure : System Diagnostics Click the test you want to run. http://h30434.www3.hp.com/t5/Notebook-Boot-and-Lockup/Can-t-Get-Past-Manufacturer-Boot-Screen/td-p/264843 I have an HP Pavillion notebook PC, running Windows 7 64bit that I bought a little over two years ago(end of 2010), and it will not go past the windows startup Hp Laptop Wont Boot Windows 10 Press the Power button to turn on the computer. Hp Laptop Wont Go Past Startup Screen Do not continue if you have important files on the hard drive that have not been backed up.

Condition Possible action LEDs do not glow and the fan or hard drive does not spin. http://flvtomp4mac.com/hp-laptop/cannot-boot-hovers-on-black-screen-after-hp-logo.php Smart Failure, Smart Failure Imminent, or S.M.A.R.T. All other startup problems For all other startup problems, see Step 4: Run Hardware Diagnostics tests. On the Choose an option screen, select Troubleshoot. Hp Laptop Stuck On Startup Screen

Is there anythng else i should do? NOTE: Do not provide the serial number. caution: This product contains components that can be damaged by electrostatic discharge (ESD). my review here Verify that a hard drive name is listed from the main screen.

Z7_3054ICK0KGTE30AQO5O3KA3016 hp-feedback-input-portlet Actions ${title} Loading... Hp Laptop Wont Boot Past Welcome Screen Click the Start button and you will be prompted to restart the Check Disk utility upon restarting of the PC to enable the utility. When I try every option in F8 it does not work and simply restarts.

Find Solutions, ask questions, and share advice with other HP product owners.

Figure : Power adapter and cord Wait 30 minutes and check the temperature of the adapter again. Figure : Startup Repair Perform the actions suggested by Startup Repair: system restore, correct damaged or missing files, or other action. I am running windows 7, but not sure if that matters at the point I'm at because the windows screen doesn't even display. Computer Wont Load Past Hp Screen Figure : Serial ATA (SATA) power and data cable connections on a hard drive Find the data cable connection to the hard drive.

note: Not all AC adapters have a light. If the computer starts and opens Windows, you are done. warning: The edges of metal panels can cut skin. get redirected here Use the up or down arrow key to select the CD/DVD drive.

Figure : Command console To close the Command Prompt, type exit to close the Command Prompt, and then press Enter. From the UEFI main menu, click System Tests, then click Fast Test. Reestablishes the connection between the BIOS and the hardware The following conditions can be helped by the hard reset: Windows stops responding. Remove any media from the floppy drives, CD/DVD drives, USB ports, and memory card reader slots, and disconnect all non-essential devices (printers, scanners, external hard drives, and similar).

Enter the product key from the side panel of the computer. Step 2: Disconnect and reconnect the hard drive cable (Desktops) Use the following steps to remove and reseat the hard drive cables: caution: This product contains components that can be damaged A System Recovery Options window opens. Step 6: Check the power cabling when troubleshooting the hard drive The black or brown 4-pin drive power headers on the system board are keyed so the drive power cable can

Video on resetting a notebook with a sealed battery View this video on YouTube. Remove and replace the CMOS battery, and then correct the time to prevent this error message from reoccurring. Turn off the computer. When it is operating correctly, it should feel slightly warm to the touch after it has been plugged in for a short time.

An error message displays on a blue screen To learn more about troubleshooting blue screen error messages, see Troubleshooting Blue Screen Error Messages that May Display During Startup or Boot (Windows Figure : Troubleshoot screen Click Next. Figure : Apply Defaults and Exit Select Yes, then press Enter.